rolling rear fenders - Honda Accord Forum : V6 Performance Accord Forums
Ribbon Banner

Go Back   Honda Accord Forum : V6 Performance Accord Forums > CAR SPECIFIC DISCUSSION > 7TH GENERATION HONDA ACCORD (2003-2007) > 7G HONDA ACCORD EXTERIOR/INTERIOR MODS
Register FAQ Members List Calendar Mark Forums Read Insurance
V6Performance.net is the premier Honda Accord Forum on the internet. Registered Users do not see the above ads.
Like Tree4Likes
  • 2 Post By toinkee69
  • 1 Post By 3.0UALLKNOW
  • 1 Post By toinkee69

Reply
 
LinkBack Thread Tools Display Modes
Old February 27th, 2013, 04:47 PM   #1
Registered User
 
05accord6spd's Avatar
 
Join Date: Feb 2012
Location: Minnesota
Posts: 424
rolling rear fenders

okay so its getting to be spring here in mn i figure 3 more weeks to pick a new set of rims and the get my fenders rolled, i need tips or tricks on how to do this. i have no problem paying money for this to be done by a shop or to roll them myself. also wondering if i should cut them? problems with waviness? or rust proofing for our cars specifically, i already know way to do this just wondering how you all did your cars. thanks guys

i just want to share my pics when im done! help a guy out!
05accord6spd is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old February 27th, 2013, 05:35 PM   #2
Kevin
 
Nguyen-er's Avatar
 
Join Date: Mar 2010
Location: Houston | Dallas
Posts: 718
Send a message via Skype™ to Nguyen-er
Just roll them flush. The area near the rear bumper is where you need it the most flush. Where are you located?

Sent from my SGH-T999 using Tapatalk 2
__________________
Understeer is when you hit the wall with the front of the car and oversteer is when you hit the wall with the rear of the car. Horsepower is how fast you hit the wall and torque is how far you take the wall with you.

Silence your enemies with success
Nguyen-er is offline   Reply With Quote Quick reply to this message
Old February 27th, 2013, 06:49 PM   #3
JDM UC1
 
toinkee69's Avatar
 
Join Date: Aug 2008
Location: socal
Posts: 8,395
diy fender rolling - YouTube
toinkee69 is offline   Reply With Quote Quick reply to this message
 
Old February 27th, 2013, 06:57 PM   #4
Registered User
 
3.0UALLKNOW's Avatar
 
Join Date: Aug 2009
Location: Tustin, CA
Posts: 989
that video is jdm as fuqqq!!
michaellowrider likes this.
3.0UALLKNOW is offline   Reply With Quote Quick reply to this message
Old February 27th, 2013, 11:41 PM   #5
Registered User
 
05accord6spd's Avatar
 
Join Date: Feb 2012
Location: Minnesota
Posts: 424
well are there any problems to watch for, waves in the fender after doing it, sealing it so it wont rust, tab relocations, once again asking how you all did it. im located in minnesota
05accord6spd is offline   Reply With Quote Quick reply to this message
Old February 28th, 2013, 05:48 PM   #6
JDM UC1
 
toinkee69's Avatar
 
Join Date: Aug 2008
Location: socal
Posts: 8,395
you'll see waves in the process of rolling. but you or the one rolling it can actually prevent it from being permanent by being careful in rolling. apply loads of heat and take your time in rolling. rushing things will make the end result not pleasant.

sealing, i duno. i live in socal, so rust is least of my problems.but i doubt the seal between the metals would tear, so you'll be good. if in doubt, just apply some silicone to seal 'em after the roll.

tab relocation depends on how low you wanna go. but since your there already, might as well. here's a tutorial about it.

Fender Rolling 101 - Password:JDM Mitsubishi EVO X - YouTube

upon rolling you'll see the quarter panel flex a bit just where it meats the bumper tabs. the metal there is thick and you won't be able to roll it. you can cut and hammer it down. but you can leave it as is if you don't need it be flat.
invsblduck likes this.
toinkee69 is offline   Reply With Quote Quick reply to this message
Old February 28th, 2013, 06:29 PM   #7
Registered User
 
05accord6spd's Avatar
 
Join Date: Feb 2012
Location: Minnesota
Posts: 424
thanks for the reply
05accord6spd is offline   Reply With Quote Quick reply to this message
Old March 5th, 2013, 09:31 AM   #8
Registered User
 
05accord6spd's Avatar
 
Join Date: Feb 2012
Location: Minnesota
Posts: 424
sorry for dub post but i needed to ask another question, without waiting for some one to post,

okay so rolling rear fender, should i roll flat? i need some one to pm me or help me out, and then im putting 9.5 18s on am i going to have to remove the front fender liner ?

it would just be nice if some one could chat or give me all the info. its my first time doing this do not want to mess it up and apparently its different on hondas than most cars, rear fender tab relocation, rolling flat etc rust proofing and so on

Last edited by 05accord6spd; March 5th, 2013 at 09:47 AM..
05accord6spd is offline   Reply With Quote Quick reply to this message
Old March 5th, 2013, 05:53 PM   #9
JDM UC1
 
toinkee69's Avatar
 
Join Date: Aug 2008
Location: socal
Posts: 8,395
can't wait, pm, chat, phone?



i gave you all the info above. you haven't even started and your expecting more help already? just go to a professional and pay for it if you don't know what you doing.
toinkee69 is offline   Reply With Quote Quick reply to this message
Old March 5th, 2013, 06:17 PM   #10
Registered User
 
05accord6spd's Avatar
 
Join Date: Feb 2012
Location: Minnesota
Posts: 424
ive got major problems with a.d.d it appears! just worrying my self over nothing. very sorry
05accord6spd is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply


Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Honda Accord Forum : V6 Performance Accord Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Chapter
Choose your AV6 Chapter Location
Ride
What do you drive?
Insurance
Please select your insurance company (Optional)

Log-in


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On