Accord V6 Forum banner

1 - 20 of 40 Posts

·
Registered
Joined
·
117 Posts
Discussion Starter #1 (Edited)
J32A2 Type-S Complete Motor, all services done*Houston, TX* Must Sell -***** $500****

I'm putting the 3.6 in my car tomorrow and must sell this one since i have no room to keep it.

*Wire Harness not included.
*Will have sensors to work with auto transmission.
*Will Ship for $350 (to lower 48 states)


Asking Price $900
NEW PRICE $500. NEED IT GONE GUYS


Call me at 832-247-9668

Also have the stock type-S ecu for an additional $100

Email me at [email protected] for faster response.



Spent over $600 in maintenance alone less than 3000 miles ago.
About 4 oil changes have been done with in that time period.

Complete Timing Belt Service.
Valve Adjustment.
All Seals Replaced.
Tensioner Replaced.

Some other stuff, cant remember


The only thing I didnt do to this motor was Valve cover gaskets and spark plugs. There was no need to.

The motor runs flawlessly. Has about 130k original miles and has been very well maintained.
Its still in the car, but will be out tomorrow morning. I have tried making a video of it, but my camera has extremely bad audio quality.

Pretty dirty in pictures, but here they are




 

·
Registered
Joined
·
117 Posts
Discussion Starter #5
sorry guys. forgot to put the price on there. but its 900. This is an awesome deal for anybody that understnad, specially because of all the money put into it.
 

·
03 Accord 6/6, 09 Audi A4
Joined
·
201 Posts
Im sure you need the ECU and sensors but other than that its almost a direct swap i believe. search the forums on the J32 swap for a complete list. sweet deal here though. just wish it had the ecu. GLWS
 

·
03 Accord 6/6, 09 Audi A4
Joined
·
201 Posts
Then its a hell of a deal ....about 1300$ for around what..60HP??thats a very good deal for the amount of engine you gain over say a J30A1
 

·
DAT Dewd from Dallas MANG
Joined
·
1,533 Posts
Yo...

fOR 900 i must pass at this time...the only thing I wanted was the block so I could start on my own 3.6 build...GLWS:up:
 

·
03 Accord 6/6, 09 Audi A4
Joined
·
201 Posts
Wish i could do it but i have nowhere to store it if i bought this and downtown Denver storage isnt cheap. Would be a waste of money having to store it til i can get my complete swap and parts list 2gether. very counter-productive. Lol. GLWS.
 

·
Registered
Joined
·
117 Posts
Discussion Starter #13
fOR 900 i must pass at this time...the only thing I wanted was the block so I could start on my own 3.6 build...GLWS:up:
u cant build a 3.6L with a 3.2 block. U need an odyssey block.

how much would you be willing to pay for the motor?
 

·
Registered
Joined
·
117 Posts
Discussion Starter #16
Sorry about the miss information than. Thats what i had thought.

so the 3.7 Crank will work in a 3.2 block? what will the displacement be then?
 

·
Registered
Joined
·
117 Posts
Discussion Starter #18
the bore is the same but what about the stroke?
I always thought the stroke of the 3.7 crank will not clear the 3.2 block.
 

·
DAT Dewd from Dallas MANG
Joined
·
1,533 Posts
yo...

the crank is where you get the stroke from...
J37 forged crank



J36 BLOCK SETUP

J30A4 heads, ported
07 TL-S cams
ported intake runners and intake
J32A3 block
J37 forged crank
J37 forged rods
05 RL forged pistons and rings
J37 OE bearings
J32A3 gaskets


I think both the J32a2 and J32a3 blocks can be used....
I know some ody blocks can be used...
I may end up going oddy block ( i know someone selling these for peanuts locally)
Hell the more I think about this I may just end up getting the damn engine BUILT by PAul...less work for me and more smiles on my face...also not to mention the engines he has built are pretty damn reliable and hold WOT's fairly well...
 

·
Registered
Joined
·
117 Posts
Discussion Starter #20
Thanks for that info.
it still hard to believe that j37 crank can be used in j32 block.

either way. I need to get this motor gone.

if I part out, any body interested?

head, IM, block?
 
1 - 20 of 40 Posts
Top