Accord V6 Forum banner

1 - 15 of 15 Posts

·
Registered
Joined
·
144 Posts
Discussion Starter #1 (Edited)
Honda/Acura J30A/J32A/J35A 3.0L-3.5L V-6 Engines

These kits fit the Acura and Honda 3.0L/3.2L/3.5L V-6 engines found in the following vehicles:

97-99 Acura CL V-6
01-03 Acura CL
01-03 Acura CL Type S
99-05 Acura TL
02-03 Acura TL Type S
01-05 Acura MDX
05+ Acura RL
98-05 Honda Accord V-6
99-05 Honda Odyssey
03-05 Honda Pilot





--------------------------------------------------------------------------------


ThermoBlok SPACER KIT - Honda/Acura J-Series V-6

Includes intake manifold spacer, throttle body spacer, gaskets, installation kit, bypass fitting, detailed instructions and OUTLAW ENGINEERING decals!

Price: $95.00 plus shipping ($6 US & Canada)

Payment options, shipping info, and return policies...


NOTE: Each kit varies slightly, so be sure to order the kit specifically for your year and model!





TESTING RESULTS - Honda J Series V-6

This dyno chart shows the results from the installation of a ThermoBlok kit on an '02 Acura TL Type S with no other mods. The tests were done on the same vehicle and same day, same gear, etc, immediately following the spacer installation. The vehicle was fully warmed up for both tests and no other modifications were done. It is interesting to note that without exception we seem to see greater gains on V-6 engines. It is our hypothesis that this is due to the V-6's larger intake being mounted directly above the engine where it will normally absorb more engine heat than the side mounted intake of the L4 type engines.

RESULTS: maximum gain 8.6 whp and 9.2 ft-lbs of torque at the 4900 RPM point with an average gain of 5 across the power band.





This temp chart shows the temp reduction seen at the intake runner from the installation of a ThermoBlok kit on an '00 Honda Odyssey. The tests were done on the same vehicle during a steady state 50-70 mph drive followed by idle.

RESULTS: Approximately 11°F cooler at cruise and 32°F cooler at idle.




AS U CAN SEE THEY ONLY MAKE THIS FOR THE V6 LETS CONTACT THEM TO MAKE IT FOR US 4CYL... (THIS IS NOT ONLY FOR 6TH GEN ITS FOR 7 GEN ASWELL SO EMAIL PLEASE ) THERE IS A PLACE ON THERE SITE WERE WE CAN REQUEST THEM TO MAKE THIS AND IF WE GET ENOUGH PEOPLE THEY WILL....I THINK ITS WORTH THE MONEY.... SO GO VOTE -----I WILL ALSO TRY TO GET A GROUP BUY ESTABLISHED IF WE GET THIS THREW---THANKS FOR SUPPORT


www.outlawengineering.com AND TO REQUEST/VOTE EMAIL AT : [email protected]
 

·
Registered
Joined
·
144 Posts
Discussion Starter #5
WELL GUYS GOT THE REPLY FROM COMPANY THIS IS THERE RESPONSE ----

Jose,

We have not heard much interest for this engine from Accord owners in the past. If there is reasonable demand for this engine, we would certainly produce a kit. The kit price would be in line with our other products (~$100) and would take approx. 4 weeks to develop. A bulk buy of 20 kits would be a great way to start this off.

Best regards,
Sean Morgan
Outlaw Engineering




-------- Original Message --------
Subject: Request for product
From: Jose chavez <[email protected]>
Date: Thu, May 19, 2005 11:26 pm
To: [email protected]


Can u please make this for The Honda accord 4 cyl 98-05 model I have people on our forum At www.honduh.com and www.v6p.net That want it and will be emailing soon for this product so when u get this could u update me so I can update them on forum thanks.... Also if made is there some type of group buy we can probably start....i can get ppaople togther to purchase with money if u give us a price$

Thanks ...could u write back and tell me ur reply to this..Thanks
Sincerley Jose ChaveZ
 

·
Registered
Joined
·
521 Posts
Just did the install, Its not that hard.

Just take my advice, and dont unbolt the throttle linkage. Or you'll have to figure out how it goes back together like me
 

·
keepin' it OG
Joined
·
10,188 Posts
i finally got an email from them regarding a gb.. here what they wrote to me...

Kiet,

Thank you for your interest in ThermoBlok spacer kits. We would be very interested in helping to facilitate a bulk buy with you. What forum/group would you be targeting? In general, we prefer at least 20 buys. Due to the already low price on the AcuraHonda J-Series kits, we would probably only be able to offer a 10-15% discount. Shipping in the U.S. is a flat $6 for US Postal Priority (2-4 day) delivery.

Best regards,
Sean Morgan
Outlaw Engineering
basically we need 20 people and price would be 91.50 shipped at most.. which isnt so bad than the full price..

i dunno whats dizzy up to with the negotiation.. but here just a thought.. maybe we can start can a list of whos interested and when dizzy is finished negotiating with them, we are ready to send in the money for the group buy.
 

·
Just a Regular Member now
Joined
·
963 Posts
7thgenaccd said:
can someone tell me what this kit does exactly?
Trying reading the first post! Even better, check out their site.

www.outlawengineering.com

Ok, we've got their stuff up on our store now. The only way I can get the price lower is to have a groupbuy of 20. They will not allow V6P to sell for lower than their own webstore.

As far as the 4cly Accords are concerned, I'll start a new poll. We have to get 20 people w/ money in hand to get this going.

Dizzy
 

·
Registered
Joined
·
1,136 Posts
hey, im down if the power is worth it. And do these things make that hissing noise like some wrx's have or thats something else? and i guess it's for auto as well as man. tranny i used to think it was only manual transmissions.

another toy to buy, so lets jump on this and show some interest.
 
1 - 15 of 15 Posts
Top